print

TPI Locations

• Corporate Headquarters - Scottsdale, AZ 
• Development and Manufacturing - Warren, RI
• Manufacturing - Springfield, OH
• Manufacturing - Newton, Iowa
• Manufacturing - Ciudad Juarez, Mexico
• Manufacturing - Taicang, China

 Corporate Headquarters - Scottsdale, AZ                               

TPI Composites
8501 N Scottsdale Rd
Gainey Center II
Suite 280
Scottsdale AZ 85253

tel 480.305.8910
fax 480.305.8315

From Sky Harbor Phoenix International Airport

• Take a Left onto Sky Harbor Blvd
• Take AZ -202 Ramp East Towards Tempe
• Take the McClintock Exit to the Left  
• McClintock turns into Hayden
• Take Hayden to Indian Bend
• Turn Left onto Indian Bend
• Turn Right onto Scottsdale Rd
• End at 8501 N Scottsdale Rd 

 Development and Manufacturing - Warren, RI

TPI Composites, Inc.
PO Box 367
373 Market Street
Warren, RI 02885-0367
tel 401.247.4010
fax 401.247.2669

Getting to Route I-195

• From the Boston area, take I-95 South towards Providence. exit left onto I-195 East (Exit #20) toward Cape Cod/Fall River and follow the remaining directions below.
• From T. F. Green Airport in Warwick, RI, take I-95 North towards Providence then take I-195 East (Exit #20)toward Cape Cod and Fall River. Continue following the remaining directions below.
• From I-95 in Providence, take I-195 East (Exit #20) toward Cape Cod and Fall River. Continue following the directions below.

Remaining directions traveling East on Route I-195

• Pass Exits #1 through #8 in Rhode Island. When you enter Massachusetts the exit numbers will restart at 1.
• Take Exit #2 Route 136 towards Warren and Newport.
• Bear right at the end of the ramp onto Route 136 South.
• Go straight through the light, crossing Rt. 6 by Dunkin Donuts and continue to follow Route 136 South about one mile. Along the way you will pass the Swansea Country Club just before you enter the town of Warren.
• Route 136 turns into Market Street.
• TPI Composites is on the left, a large tan building with brown overhead doors, across the street from the Country Inn restaurant.
• Turn left into the driveway after passing the building (by the flag pole and palm trees).
• Drive along the front of the plant, to the left, then bear right through the large parking area to the entrance to the office building which is attached to the plant.
• Please call 401.247.4010 for additional information.

 Manufacturing - Springfield, OH

TPI Ohio 

2145 Airpark Dr
Springfield, OH 45502
tel 937.322.1433
fax 937.322.1390

From Port Columbus International Airport

• Turn right onto Sawyer Road and head West
• Turn left at International Gateway
• Take the I-670 W/US-62 W ramp
• Merge onto I-670 W
• Take the exit onto I-670 W
• Merge onto I-70 W
• Take exit 52A to merge onto US-68 S toward Xenia
• Turn left at Airpark Drive

From Dayton International Airport

• Head southeast toward Cargo Road
• Continue straight onto Terminal Drive (signs for Dayton/I-70 E/I-75 S)
• Continue on Dayton International Airport Access Road
• Take the exit onto I-70 E toward Columbus
• Take exit 52A to merge onto US-68 S toward Xenia
• Turn left at Airpark Drive

  Manufacturing - Newton, Iowa                                      

TPI Iowa

2300 N 33rd Ave E
PO Box 847 
Newton, IA 50208 

tel: 641-791-3500

fax: 641-791-3550

Directions to TPI- Iowa from Des Moines International Airport

• From Airport turn left (North) onto Fleur Drive
• Fleur Drive will become Martin Luther King Jr. Pkwy.
• Merge onto I-235 East (approximately 6.5 miles)
• Take I-80 East exit toward Davenport to Newton Exit 168 (approximately 26.5 miles)
• Continue on I-80 East to Exit 168 – Newton – Iowa Speedway Exit
• Turn left off exit heading North (under I-80)
• Continue North through stop light (1st Ave E. and E. 31st St N./Beltline Road) Approximately 1.5 miles.
• Road curves heading West
• At top of hill (N. 19thAve E. and E. 19thStreet N.) turn right (North)
• Continue on 19th Street to 33rd Ave. (approximately 1 mile)
• Turn right (East) on N. 33rd Ave. E.
• TPI will be on your left (4.8 miles from I-80 exit)
• Enter through double glass doors with overhang

 Manufacturing - Ciudad Juarez, Mexico

Mailing Address
VienTek Mexico
PostNet
3737 No Mesa, Suite D1
El Paso, TX 79902

Street Address
Vientek Mexico S. de R.L. de C.V.
Ave. de las Torres #2251
Col. Torres del Sur C.P. 32574
Cd. Juarez, Chih. Mexico

tel 915.225.1302
fax 915.225.1337

From El Paso Airport in El Paso Texas

• Take I-10 EAST for 6 miles
• Exit onto Zaragoza Road turning RIGHT toward the SOUTH and follow for approximately 4 miles to the Mexican border.
• At the Mexican border, watch for the signal light. If the red light flashes "PASE," proceed straight. If the red light flashes "REVISION," pull to the side for inspection.
• Just after the covered inspection area turn RIGHT and park to get your visitor's permit inside the building on the west side of the inspection area.
• NOTE: YOU MUST HAVE A BUSINESS VISITORS PERMIT TO ENTER VIENTEK
• After the inspection and getting the visitors permit, continue on the same road into Mexico; bear RIGHT after a short distance as road splits, following the sign toward Juarez.
• At first light, go straight, but bear RIGHT a bit around median, this becomes Waterfil Road.
• Go about 1-1/2 miles to the next stop light and turn LEFT onto Francisco Villareal Torres.
• Before the Vientek building, you will pass a shopping center on the right called SORIANA- Plaza Las Torres.
• Follow Torres less than a mile and you will see the Vientek building on your right.
• Enter the left hand side of the guard shack, sign in with the guard and get a visitor's badge.
• Turn LEFT and come around the SOUTHEAST corner of building to Vistor's lobby.
• Please call (915) 225-1302 for additional information.

 Manufacturing - Taicang China

TPI Taicang Composites